16
2503QS–AVR–02/11
ATmega32(L)
Errata
ATmega32, rev. A
to F
First Analog Comparator conversion may be delayed
Interrupts may be lost when writing the timer registers in the asynchronous timer
IDCODE masks data from TDI input
Reading EEPROM by using ST or STS to set EERE bit triggers unexpected interrupt request.
1.
First Analog Comparator conversion may be delayed
If the device is powered by a slow rising V
CC, the first Analog Comparator conversion will
take longer than expected on some devices.
Problem Fix/Workaround
When the device has been powered or reset, disable then enable theAnalog Comparator
before the first conversion.
2.
Interrupts may be lost when writing the timer registers in the asynchronous timer
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem Fix/Workaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor
0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous-
Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx).
3.
IDCODE masks data from TDI input
The JTAG instruction IDCODE is not working correctly. Data to succeeding devices are
replaced by all-ones during Update-DR.
Problem Fix / Workaround
If ATmega32 is the only device in the scan chain, the problem is not visible.
Select the Device ID Register of the ATmega32 by issuing the IDCODE instruction or
by entering the Test-Logic-Reset state of the TAP controller to read out the contents
of its Device ID Register and possibly data from succeeding devices of the scan
chain. Issue the BYPASS instruction to the ATmega32 while reading the Device ID
Registers of preceding devices of the boundary scan chain.
If the Device IDs of all devices in the boundary scan chain must be captured
simultaneously, the ATmega32 must be the fist device in the chain.
4.
Reading EEPROM by using ST or STS to set EERE bit triggers unexpected interrupt
request.
Reading EEPROM by using the ST or STS command to set the EERE bit in the EECR reg-
ister triggers an unexpected EEPROM interrupt request.
Problem Fix / Workaround
Always use OUT or SBI to set EERE in EECR.
相关PDF资料
06FMN-BMTTN-A-TF CONN FMN HSNG 6POS STAG NOR SMD
05FMN-BMTTN-A-TF CONN FMN HSNG 5POS STAG NOR SMD
04FMN-BMTTN-A-TF CONN FMN HSNG 4POS STAG NOR SMD
40FMN-BMTR-A-TB CONN FMN HSNG 40POS SGL REV SMD
36FMN-BMTR-A-TB CONN FMN HSNG 36POS SGL REV SMD
35FMN-BMTR-A-TB CONN FMN HSNG 35POS SGL REV SMD
34FMN-BMTR-A-TB CONN FMN HSNG 34POS SGL REV SMD
29FMN-BMTR-A-TB CONN FMN HSNG 29POS SGL REV SMD
相关代理商/技术参数
ATMEGA32-16PI 功能描述:8位微控制器 -MCU AVR 32K FLASH 2KB SRAM 1KB EE RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA32-16PJ 功能描述:IC MCU AVR 32K 5V 16MHZ 40-DIP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:AVR® ATmega 标准包装:9 系列:87C 核心处理器:8051 芯体尺寸:8-位 速度:40/20MHz 连通性:UART/USART 外围设备:POR,WDT 输入/输出数:32 程序存储器容量:32KB(32K x 8) 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:0°C ~ 70°C 封装/外壳:40-DIP(0.600",15.24mm) 包装:管件
ATmega32-16PU 功能描述:8位微控制器 -MCU 32kB Flash 1kB EEPROM 32 I/O Pins RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA323 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 32K Bytes of In-System Programmable Flash
ATMEGA323(L) 制造商:未知厂家 制造商全称:未知厂家 功能描述:ATmega323(L) Summary [Updated 9/03. 18 Pages]
ATMEGA323-8AC 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 32K Bytes of In-System Programmable Flash
ATMEGA323-8AI 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 32K Bytes of In-System Programmable Flash
ATMEGA323-8PC 功能描述:8位微控制器 -MCU 32k byte RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT